preamble attached >>>
ADs updated daily at www.Tdata.com
PROPOSED AD DASSAULT AVIATION: Docket No. FAA-2022-1579; Project Identifier MCAI-2022-00903-T.
(a) COMMENTS DUE DATE

    The FAA must receive comments  on this airworthiness directive (AD) by
    January 27, 2023.

(b) AFFECTED ADS

(1) This AD replaces AD 2021-09-12,  Amendment 39-21526  (86 FR 23593, May
    4, 2021) (AD 2021-09-12).

(2) This AD affects AD 2014-16-23,  Amendment 39-17947  (79 FR 52545, Sep-
    tember 4, 2014) (AD 2014-16-23).

(c) APPLICABILITY

    This AD  applies to Dassault Aviation Model FALCON 7X airplanes,  cer-
    tificated in any category,  with an original airworthiness certificate
    or original export certificate  of  airworthiness issued  on or before
    June 7, 2021.

Note 1 to paragraph (c): Model FALCON 7X airplanes with modification M1000
incorporated are commonly referred to as "Model FALCON 8X" airplanes  as a
marketing designation.

(d) SUBJECT

    Air Transport Association (ATA) of America Code 05,  Time Limits/Main-
    tenance Checks.

(e) UNSAFE CONDITION

    This AD was prompted by  a determination that new or  more restrictive
    airworthiness limitations are necessary. The FAA is issuing this AD to
    address reduced structural integrity and reduced control of  airplanes
    due to the failure of system components.

(f) COMPLIANCE

    Comply with this AD within the compliance times specified,  unless al-
    ready done.

(g) RETAINED REVISION OF THE EXISTING MAINTENANCE  OR  INSPECTION PROGRAM,
    WITH NO CHANGES

    This paragraph restates the requirements of paragraph (j)  of AD 2021-
    09-12, with no changes.  For airplanes with an  original airworthiness
    certificate or original export certificate of airworthiness issued  on
    or before June 1, 2020, except  as specified in paragraph (h) of  this
    AD: Comply with  all required actions  and compliance times  specified
    in,  and in  accordance with,  European Union  Aviation Safety  Agency
    (EASA)  AD  2020-0214,  dated October  6,  2020  (EASA AD  2020-0214).
    Accomplishing the revision of  the existing maintenance or  inspection
    program  required  by  paragraph   (j)  of  this  AD   terminates  the
    requirements of this paragraph.

(h) RETAINED EXCEPTIONS TO EASA AD 2020-0214, WITH NO CHANGES

    This paragraph  restates the exceptions  specified in paragraph (k) of
    AD 2021-09-12, With no changes.

(1) The requirements  specified in paragraphs (1) and (2) of EASA AD 2020-
    0214 do not apply to this AD.

(2) Paragraph (3) of EASA AD 2020-0214  specifies  revising  "the approved
    AMP" within 12 months  after its effective date,  but this AD requires
    revising the existing maintenance or inspection program, as applicable
    to incorporate the "limitations,  tasks and associated thresholds  and
    intervals"  specified in paragraph (3)  of EASA AD 2020-0214 within 90
    days after June 8, 2021 (the effective date of this AD 2021-09-12).

(3) The initial compliance time for doing the tasks specified in paragraph
    (3) of EASA AD 2020-0214 is at the applicable  "associated thresholds"
    specified in paragraph (3)  of  EASA AD 2020-0214,  or  within 90 days
    after June 8, 2021  (the effective date of this AD 2021-09-12), which-
    ever occurs later.

(4) The provisions  specified  in  paragraphs (4) and (5) of EASA AD 2019-
    0257 do not apply to this AD.

(5) The "Remarks" section of EASA AD 2020-0214 does not apply to this AD.

(i) RETAINED RESTRICTIONS ON ALTERNATIVE ACTIONS, INTERVALS,  AND CRITICAL
    DESIGN CONFIGURATION CONTROL LIMITATIONS (CDCCLS) WITH A NEW EXCEPTION

    This paragraph restates the requirements of paragraph (l)  of AD 2021-
    09-12,  with a new exception.  Except as required  by paragraph (j) of
    this AD,  after the maintenance or inspection program has been revised
    as required by paragraph (g) of this AD, no alternative actions (e.g.,
    inspections), intervals or CDCCLs are allowed unless they are approved
    as specified  in the provisions  of the "Ref. Publications" section of
    EASA AD 2020-0214.

(j) NEW REVISION OF THE EXISTING MAINTENANCE OR INSPECTION PROGRAM

    Except as specified in paragraph (k)  of this AD:  Comply with all re-
    quired actions and compliance times specified in,  and  in  accordance
    with,  EASA  AD  2022-0142,  dated  July 7, 2022  (EASA AD 2022-0142).
    Accomplishing the revision  of the existing maintenance  or inspection
    program required by this paragraph terminates the requirements of par-
    agraph (g) of this AD.

(k) EXCEPTIONS TO EASA AD 2022-0142

(1) The requirements  specified in paragraphs (1) and (2) of EASA AD 2022-
    0142 do not apply to this AD.

(2) Paragraph (3) of EASA AD 2022-0142  specifies  revising  "the approved
    AMP" within 12 months after  its effective date, but this  AD requires
    revising   the  existing   maintenance  or   inspection  program,   as
    applicable, within 90 days after the effective date of this AD.

(3) The initial compliance time for doing the tasks specified in paragraph
    (3) of EASA  AD 2022-0142  is  at  the  applicable  "limitations"  and
    "associated thresholds"  as incorporated  by the requirements of para-
    graph (3) of EASA AD 2022-0142,  or within 90 days after the effective
    date of this AD, whichever occurs later.

(4) The provisions  specified  in  paragraphs (4) and (5) of EASA AD 2022-
    0142 do not apply to this AD.

(5) The "Remarks" section of EASA AD 2022-0142 does not apply to this AD.

(l) NEW PROVISIONS FOR ALTERNATIVE ACTIONS, INTERVALS, AND CDCCLS

    After the existing maintenance or inspection program  has been revised
    as required by paragraph (j) of this AD, no alternative actions (e.g.,
    inspections),  intervals,  and  CDCCLs  are  allowed  unless  they are
    approved as  specified in  the provisions  of the  "Ref. Publications"
    section of EASA AD 2022-0142.

(m) TERMINATING ACTION FOR CERTAIN REQUIREMENTS IN AD 2014-16-23

    Accomplishing the actions required by paragraphs (g) or (j) of this AD
    terminates the requirements of paragraph (q) of AD 2014-16-23.

(n) ADDITIONAL AD PROVISIONS

    The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs):  The Manager, International
    Validation Branch, FAA, has the authority to approve AMOCs for this AD
    if requested using the procedures found in 14 CFR 39.19. In accordance
    with 14 CFR 39.19,  send your request  to your principal inspector  or
    responsible Flight Standards Office, as appropriate. If sending infor-
    mation directly to the International Validation Branch, send it to the
    attention of the person identified in paragraph (o) of this AD. Infor-
    mation may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any
    approved AMOC, notify your appropriate principal inspector, or lacking
    a principal inspector, the manager of the responsible Flight Standards
    Office.

(2) Contacting the Manufacturer:  For any requirement in this AD to obtain
    instructions   from   a  manufacturer,   the   instructions  must   be
    accomplished using  a method  approved by  the Manager,  International
    Validation Branch, FAA;  or EASA; or  Dassault Aviation's EASA  Design
    Organization Approval (DOA). If approved by the DOA, the approval must
    include the DOA-authorized signature.

(o) ADDITIONAL INFORMATION

    For more information about this AD,  contact Tom Rodriguez,  Aerospace
    Engineer, Large Aircraft Section, International Validation Branch, FAA
    2200 South 216th St., Des Moines, WA 98198; telephone and fax 206-231-
    3226; email tom.rodriguez@faa.gov.

(p) MATERIAL INCORPORATED BY REFERENCE

(1) The Director of the Federal Register  approved  the  incorporation  by
    reference of the service information  listed in this paragraph under 5
    U.S.C. 552(a) and 1 CFR part 51.

(2) You must use this service information as applicable  to do the actions
    required by this AD, unless this AD specifies otherwise.

(3) The following service information  was  approved  for  IBR on [DATE 35
    DAYS AFTER PUBLICATION OF THE FINAL RULE].

(i) European Union Aviation Safety Agency (EASA) AD 2022-0142,  dated July
    7, 2022.

(ii) [Reserved]

(4) The following service information was approved for IBR on June 8, 2021
    (86 FR 23593, May 4, 2021).

(i) European Union Aviation Safety Agency (EASA) AD 2020-0214, dated Octo-
    ber 6, 2020.

(ii) [Reserved]

(5) For EASA ADs 2022-0142 and 2020-0214,  contact EASA,  Konrad-Adenauer-
    Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@
    easa.europa.eu; website easa.europa.eu. You may find these EASA ADs on
    the EASA website at ad.easa.europa.eu.

(6) You may view this material at the FAA, Airworthiness Products Section,
    Operational Safety Branch,  2200 South 216th St., Des Moines, WA.  For
    information on the availability of this material at the FAA, call 206-
    231-3195.

(7) You may view  this material  that is incorporated by reference  at the
    National Archives and Records Administration (NARA).  For  information
    on the availability of this material at NARA, email fr.inspection@nara
    .gov, or go to: archives.gov/federal-register/cfr/ibr-locations.html.

Issued on December 6, 2022.  Christina Underwood, Acting Director, Compli-
ance & Airworthiness Division, Aircraft Certification Service.

DATES: The FAA must receive comments  on  this  proposed AD by January 27,
2023.
PREAMBLE 

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2022-1579; Project Identifier MCAI-2022-00903-T]
RIN 2120-AA64

Airworthiness Directives; Dassault Aviation Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to supersede Airworthiness Directive (AD)
2021-09-12, which applies to certain Dassault Aviation Model FALCON 7X
airplanes. AD 2021-09-12 requires revising the existing maintenance or
inspection program, as applicable, to incorporate new or more
restrictive airworthiness limitations. Since the FAA issued AD 2021-09-
12, the FAA has determined that new or more restrictive airworthiness
limitations are necessary. This proposed AD would continue to require
the actions in AD 2021-09-12 and require revising the existing
maintenance or inspection program, as applicable, to incorporate
additional new or more restrictive airworthiness limitations, as
specified in a European Union Aviation Safety Agency (EASA) AD, which
is proposed for incorporation by reference (IBR). The FAA is proposing
this AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by January 27,
2023.

ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
Federal eRulemaking Portal: Go to regulations.gov. Follow
the instructions for submitting comments.
Fax: 202-493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.
Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
AD Docket: You may examine the AD docket at regulations.gov under
Docket No. FAA-2022-1579; or in person at Docket Operations between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD
docket contains this NPRM, the mandatory continuing airworthiness
information (MCAI), any comments received, and other information. The
street address for Docket Operations is listed above.
Material Incorporated by Reference:
For material that is proposed for IBR in this NPRM,
contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone
+49 221 8999 000; email ADs@easa.europa.eu; website easa.europa.eu. You
may find this material on the EASA website at ad.easa.europa.eu. It is
also available at regulations.gov under Docket No. FAA-2022-1579.
You may view this service information at the FAA,
Airworthiness Products Section, Operational Safety Branch, 2200 South
216th St., Des Moines, WA. For information on the availability of this
material at the FAA, call 206-231-3195.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer,
Large Aircraft Section, International Validation Branch, FAA, 2200
South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3226;
email tom.rodriguez@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

The FAA invites you to send any written relevant data, views, or
arguments about this proposal. Send
your comments to an address listed under ADDRESSES. Include ``Docket
No. FAA-2022-1579; Project Identifier MCAI-2022-00903-T'' at the
beginning of your comments. The most helpful comments reference a
specific portion of the proposal, explain the reason for any
recommended change, and include supporting data. The FAA will consider
all comments received by the closing date and may amend this proposal
because of those comments.
Except for Confidential Business Information (CBI) as described in
the following paragraph, and other information as described in 14 CFR
11.35, the FAA will post all comments received, without change, to
regulations.gov, including any personal information you provide. The
agency will also post a report summarizing each substantive verbal
contact received about this NPRM.

Confidential Business Information

CBI is commercial or financial information that is both customarily
and actually treated as private by its owner. Under the Freedom of
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public
disclosure. If your comments responsive to this NPRM contain commercial
or financial information that is customarily treated as private, that
you actually treat as private, and that is relevant or responsive to
this NPRM, it is important that you clearly designate the submitted
comments as CBI. Please mark each page of your submission containing
CBI as ``PROPIN.'' The FAA will treat such marked submissions as
confidential under the FOIA, and they will not be placed in the public
docket of this NPRM. Submissions containing CBI should be sent to Tom
Rodriguez, Aerospace Engineer, Large Aircraft Section, International
Validation Branch, FAA, 2200 South 216th St., Des Moines, WA 98198;
telephone and fax 206-231-3226; email tom.rodriguez@faa.gov. Any
commentary that the FAA receives that is not specifically designated as
CBI will be placed in the public docket for this rulemaking.

Background

The FAA issued AD 2021-09-12, Amendment 39-21526 (86 FR 23593, May
4, 2021) (AD 2021-09-12), for certain Dassault Aviation Model FALCON 7X
airplanes. AD 2021-09-12 was prompted by MCAI originated by EASA, which
is the Technical Agent for the Member States of the European Union.
EASA issued AD 2020-0214, dated October 6, 2020 (EASA AD 2020-0214)
(which corresponds to FAA AD 2021-09-12), to correct an unsafe
condition.
AD 2021-09-12 requires revising the existing maintenance or
inspection program, as applicable, to incorporate new or more
restrictive airworthiness limitations. The FAA issued AD 2021-09-12 to
address reduced structural integrity and reduced control of airplanes
due to the failure of system components. AD 2021-09-12 specifies that
accomplishing the revision required by that AD terminates certain
requirements of AD 2014-16-23, Amendment 39-17947 (79 FR 52545,
September 4, 2014) (AD 2014-16-23).

Actions Since AD 2021-09-12 Was Issued

Since the FAA issued AD 2021-09-12, EASA superseded EASA AD 2020-
0214 and issued EASA AD 2022-0142, dated July 7, 2022 (EASA AD 2022-
0142) (referred to after this as the MCAI), for all Dassault Aviation
Model FALCON 7X airplanes. The MCAI states that new or more restrictive
airworthiness limitations have been issued.
Airplanes with an original airworthiness certificate or original
export certificate of airworthiness issued after June 7, 2021 must
comply with the airworthiness limitations specified as part of the
approved type design and referenced on the type certificate data sheet;
this proposed AD therefore does not include those airplanes in the
applicability.
The FAA is proposing this AD to address reduced structural
integrity and reduced control of airplanes due to the failure of system
components. You may examine the MCAI in the AD docket at
regulations.gov under Docket No. FAA-2022-1579.

Related Service Information Under 1 CFR Part 51

The FAA reviewed EASA AD 2022-0142. This service information
specifies new or more restrictive airworthiness limitations for
airplane structures and safe life limits.
This proposed AD would also require EASA AD 2020-0214, dated
October 6, 2020, which the Director of the Federal Register approved
for incorporation by reference as of June 8, 2021 (86 FR 23593, May 4,
2021).
This material is reasonably available because the interested
parties have access to it through their normal course of business or by
the means identified in ADDRESSES.

FAA's Determination

This product has been approved by the aviation authority of another
country and is approved for operation in the United States. Pursuant to
the FAA's bilateral agreement with the State of Design Authority, it
has notified the FAA of the unsafe condition described in the MCAI
described above. The FAA is issuing this NPRM after determining that
the unsafe condition described previously is likely to exist or develop
in other products of the same type design.

Proposed AD Requirements in This NPRM

This proposed AD would retain certain requirements of AD 2021-09-
12. This proposed AD would also require revising the existing
maintenance or inspection program, as applicable, to incorporate
additional new or more restrictive airworthiness limitations, which are
specified in EASA AD 2022-0142 already described, as proposed for
incorporation by reference. Any differences with EASA AD 2022-0142 are
identified as exceptions in the regulatory text of this AD.
This proposed AD would require revisions to certain operator
maintenance documents to include new actions (e.g., inspections) and
Critical Design Configuration Control Limitations (CDCCLs). Compliance
with these actions and CDCCLs is required by 14 CFR 91.403(c). For
airplanes that have been previously modified, altered, or repaired in
the areas addressed by this proposed AD, the operator may not be able
to accomplish the actions described in the revisions. In this
situation, to comply with 14 CFR 91.403(c), the operator must request
approval for an alternative method of compliance (AMOC) according to
paragraph (n)(1) of this proposed AD.

Explanation of Required Compliance Information

In the FAA's ongoing efforts to improve the efficiency of the AD
process, the FAA developed a process to use some civil aviation
authority (CAA) ADs as the primary source of information for compliance
with requirements for corresponding FAA ADs. The FAA has been
coordinating this process with manufacturers and CAAs. As a result, the
FAA proposes to retain the IBR of EASA AD 2020-0214 and incorporate
EASA AD 2022-0142 by reference in the FAA final rule. This proposed AD
would, therefore, require compliance with EASA AD 2022-0142 and EASA AD
2020-0214 through that incorporation, except for any differences
identified as exceptions in the regulatory text of this proposed AD.
Using common terms that are the same as the heading of a particular
section in EASA AD 2022-0142 or EASA AD 2020-0214 does not mean that operators
need comply only with that section. For example, where the AD
requirement refers to ``all required actions and compliance times,''
compliance with this AD requirement is not limited to the section
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2022-
0142 or EASA AD 2020-0214. Service information required by EASA AD
2022-0142 and EASA AD 2020-0214 for compliance will be available at
regulations.gov by searching for and locating Docket No. FAA-2022-1579
after the FAA final rule is published.

Airworthiness Limitation ADs Using the New Process

The FAA's process of incorporating by reference MCAI ADs as the
primary source of information for compliance with corresponding FAA ADs
has been limited to certain MCAI ADs (primarily those with service
bulletins as the primary source of information for accomplishing the
actions required by the FAA AD). However, the FAA is now expanding the
process to include MCAI ADs that require a change to airworthiness
limitation documents, such as airworthiness limitation sections.
For these ADs that incorporate by reference an MCAI AD that changes
airworthiness limitations, the FAA requirements are unchanged.
Operators must revise the existing maintenance or inspection program,
as applicable, to incorporate the information specified in the new
airworthiness limitation document. The airworthiness limitations must
be followed according to 14 CFR 91.403(c) and 91.409(e).
The previous format of the airworthiness limitation ADs included a
paragraph that specified that no alternative actions (e.g.,
inspections), intervals, or CDCCLs may be used unless the actions,
intervals, and CDCCLs are approved as an AMOC in accordance with the
procedures specified in the AMOCs paragraph under ``Additional AD
Provisions.'' This new format includes a ``New Provisions for
Alternative Actions, Intervals, and CDCCLs'' paragraph that does not
specifically refer to AMOCs, but operators may still request an AMOC to
use an alternative action, interval, or CDCCL.

Costs of Compliance

The FAA estimates that this AD, if adopted as proposed, would
affect 122 airplanes of U.S. registry. The FAA estimates the following
costs to comply with this proposed AD:
The FAA estimates the total cost per operator for the retained
actions from AD 2021-09-12 to be $7,650 (90 work-hours x $85 per work-
hour).
The FAA has determined that revising the existing maintenance or
inspection program takes an average of 90 work-hours per operator,
although the agency recognizes that this number may vary from operator
to operator. Since operators incorporate maintenance or inspection
program changes for their affected fleet(s), the FAA has determined
that a per-operator estimate is more accurate than a per-airplane
estimate.
The FAA estimates the total cost per operator for the new proposed
actions to be $7,650 (90 work-hours x $85 per work-hour).

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.

Regulatory Findings

The FAA determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Would not affect intrastate aviation in Alaska, and
(3) Would not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended]

2. The FAA amends Sec. 39.13 by:

a. Removing Airworthiness Directive (AD) 2021-09-12, Amendment 39-21526
(86 FR 23593, May 4, 2021); and

b. Adding the following new AD: