preamble attached >>>
ADs updated daily at www.Tdata.com
PROPOSED AD MHI RJ AVIATION ULC (TYPE CERTIFICATE PREVIOUSLY HELD BY BOMBARDIER, INC.): Docket No. FAA-2021-0382; Project Identifier MCAI-2021-00382-T.
(a) COMMENTS DUE DATE

    The FAA must receive comments  on this airworthiness directive (AD) by
    July 12, 2021.

(b) AFFECTED ADS

    None.

(c) APPLICABILITY

    This AD applies to MHI RJ Aviation ULC  airplanes  identified in para-
    graphs (c)(1) through (3) of this AD, certificated in any category.

(1) Model CL-600-2C10 (Regional Jet Series 700, 701 & 702) and CL-600-2C11
    (Regional Jet Series 550) airplanes,  serial numbers  10002 and subse-
    quent.

(2) Model CL-600-2D15 (Regional Jet Series 705)  and CL-600-2D24 (Regional
    Jet Series 900) airplanes, serial numbers 15001 and subsequent.

(3) Model CL-600-2E25 (Regional Jet Series 1000) airplanes, serial numbers
    19001 and subsequent.

(d) SUBJECT

    Air Transport Association (ATA)  of America Code 05,  Periodic Inspec-
    tions.

(e) UNSAFE CONDITION

    This AD was prompted by a determination that new airworthiness limita-
    tions  for  structural  inspections  and  safe  life  components   are
    necessary. The FAA  is issuing this  AD to address  reduced structural
    integrity and reduced controllability of the airplane.

(f) COMPLIANCE

    Comply with this AD within the compliance times specified,  unless al-
    ready done.

(g) MAINTENANCE OR INSPECTION PROGRAM REVISION

    Within 180 days after the effective date of this AD, revise the exist-
    ing maintenance or inspection program,  as applicable,  to incorporate
    the airworthiness limitations for structural inspections and safe life
    components specified in paragraphs (g)(1) and (2) of this AD.

(1) The task number,  model effectivity, threshold, repeat cut-in, repeat,
    and task type  for  the  Section 2 structural inspections specified in
    paragraph 2.B.(2)(a)  of  the  Accomplishment Instructions  of  MHI RJ
    Service Bulletin 670BA-05-001, dated August 27, 2020.

(2) The task number, part number, model effectivity,  and discard time for
    the Section 3 safe life components specified  in  paragraph 2.B.(3)(a)
    of the Accomplishment Instructions of MHI RJ Service Bulletin 670BA-05
    -001, dated August 27, 2020.

(h) NO ALTERNATIVE ACTIONS AND INTERVALS

    After the existing maintenance or inspection program  has been revised
    as required by paragraph (g) of this AD, no alternative actions (e.g.,
    inspections) or intervals may be used unless the actions and intervals
    are  approved  as  an  alternative  method  of  compliance  (AMOC)  in
    accordance with the procedures  specified in paragraph (i)(1)  of this
    AD.

(i) OTHER FAA AD PROVISIONS

    The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs):  The Manager,  New York ACO
    Branch,  FAA,  has  the authority  to approve  AMOCs for  this AD,  if
    requested using the  procedures found in  14 CFR 39.19.  In accordance
    with 14 CFR  39.19, send your  request to your  principal inspector or
    responsible  Flight  Standards  Office,  as  appropriate.  If  sending
    information directly to the manager of the certification office,  send
    it to ATTN: Program  Manager, Continuing Operational Safety,  FAA, New
    York ACO Branch, 1600 Stewart  Avenue, Suite 410, Westbury, NY  11590;
    telephone 516-228-7300;  fax 516-794-5531.  Before using  any approved
    AMOC,  notify  your  appropriate  principal  inspector,  or  lacking a
    principal inspector, the manager  of the responsible Flight  Standards
    Office.

(2) Contacting the Manufacturer:  For any requirement in this AD to obtain
    instructions   from   a  manufacturer,   the   instructions  must   be
    accomplished using  a method  approved by  the Manager,  New York  ACO
    Branch, FAA;  or Transport  Canada Civil  Aviation (TCCA);  or MHI  RJ
    Aviation ULC's TCCA Design Approval Organization (DAO). If approved by
    the DAO, the approval must include the DAO-authorized signature.

(j) RELATED INFORMATION

(1) Refer to Mandatory Continuing Airworthiness Information (MCAI) TCCA AD
    CF-2020-53, dated December 7, 2020, for related information. This MCAI
    may be found  in  the  AD  docket  on  the  internet  at  https://www.
    regulations.gov by searching  for  and  locating  Docket No. FAA-2021-
    0382.

(2) For more information about this AD,  contact  Antariksh Shetty,  Aero-
    space Engineer,  Airframe and Propulsion Section,  FAA,  New York  ACO
    Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590;  telephone
    516-228-7300; fax 516-794-5531; email 9-avs-nyaco-cos@faa.gov.

(3) For service information identified in this AD, contact MHI RJ Aviation
    ULC, 12655 Henri-Fabre Blvd., Mirabel, Quebec J7N 1E1 Canada; Widebody
    Customer Response Center North America toll-free telephone +1-844-272-
    2720 or direct-dial  telephone +1-514-855-8500;  fax  +1-514-855-8501;
    email thd.crj@mhirj.com; internet https://mhirj.com. You may view this
    service information at the FAA, Airworthiness Products Section, Opera-
    tional Safety Branch, 2200 South 216th St., Des Moines, WA. For infor-
    mation on the availability of this material at the FAA,  call 206-231-
    3195.

Issued on May 21, 2021. Gaetano A Sciortino, Deputy Director for Strategic
Initiatives,  Compliance & Airworthiness Division,  Aircraft Certification
Service.

DATES: The FAA must receive comments on this proposed AD by July 12, 2021.
PREAMBLE 

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2021-0382; Project Identifier MCAI-2021-00382-T]
RIN 2120-AA64

Airworthiness Directives; MHI RJ Aviation ULC (Type Certificate
Previously Held by Bombardier, Inc.) Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD)
for certain MHI RJ Aviation ULC Model CL-600-2C10 (Regional Jet Series
700, 701 & 702), CL-600-2C11 (Regional Jet Series 550), CL-600-2D15
(Regional Jet Series 705), CL-600-2D24 (Regional Jet Series 900), and
CL-600-2E25 (Regional Jet Series 1000) airplanes. This proposed AD was
prompted by a determination that new airworthiness limitations for
structural inspections and safe life components are necessary. This
proposed AD would require revising the existing maintenance or
inspection program, as applicable, to incorporate new airworthiness
limitations. The FAA is proposing this AD to address the unsafe
condition on these products.

DATES: The FAA must receive comments on this proposed AD by July 12,
2021.

ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:

Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the
instructions for submitting comments.

Fax: 202-493-2251.

Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.

Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this NPRM, contact MHI RJ
Aviation ULC, 12655 Henri-Fabre Blvd., Mirabel, Qu[eacute]bec J7N 1E1
Canada; Widebody Customer Response Center North America toll-free
telephone +1-844-272-2720 or direct-dial telephone +1-514-855-8500; fax
+1-514-855-8501; email thd.crj@mhirj.com; internet https://mhirj.com.
You may view this service information at the FAA, Airworthiness
Products Section, Operational Safety Branch, 2200 South 216th St., Des
Moines, WA. For information on the availability of this material at the
FAA, call 206-231-3195.

Examining the AD Docket

You may examine the AD docket at https://www.regulations.gov by
searching for and locating Docket No. FAA-2021-0382; or in person at
Docket Operations between 9 a.m. and 5 p.m., Monday through Friday,
except Federal holidays. The AD docket contains this NPRM, any comments
received, and other information. The street address for Docket
Operations is listed above.

FOR FURTHER INFORMATION CONTACT: Antariksh Shetty, Aerospace Engineer,
Airframe and Propulsion Section, FAA, New York ACO Branch, 1600 Stewart
Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7300; fax 516-
794-5531; email 9-avs-nyaco-cos@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

The FAA invites you to send any written relevant data, views, or
arguments about this proposal. Send your comments to an address listed
under ADDRESSES. Include "Docket No. FAA-2021-0382; Project Identifier
MCAI-2021-00382-T" at the beginning of your comments. The most helpful
comments reference a specific portion of the proposal, explain the
reason for any recommended change, and include supporting data. The FAA
will consider all comments received by the closing date and may amend
the proposal because of those comments.

Except for Confidential Business Information (CBI) as described in
the following paragraph, and other information as described in 14 CFR
11.35, the FAA will post all comments received, without change, to
https://www.regulations.gov, including any personal information you
provide. The agency will also post a report summarizing each
substantive verbal contact received about this NPRM.

Confidential Business Information

CBI is commercial or financial information that is both customarily
and actually treated as private by its owner. Under the Freedom of
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public
disclosure. If your comments responsive to this NPRM contain commercial
or financial information that is customarily treated as private, that
you actually treat as private, and that is relevant or responsive to
this NPRM, it is important that you clearly designate the submitted
comments as CBI. Please mark each page of your submission containing
CBI as "PROPIN." The FAA will treat such marked submissions as
confidential under the FOIA, and they will not be placed in the public
docket of this NPRM. Submissions containing CBI should be sent to
Antariksh Shetty, Aerospace Engineer, Airframe and Propulsion Section,
FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY
11590; telephone 516-228-7300; fax 516-794-5531; email 9-avs-nyaco-cos@
faa.gov. Any commentary that the FAA receives which is not specifically
designated as CBI will be placed in the public docket for this rulemaking.

Background

Transport Canada Civil Aviation (TCCA), which is the aviation
authority for Canada, has issued TCCA AD CF-2020-53, dated December 7,
2020 (also referred to after this as the Mandatory Continuing
Airworthiness Information, or the MCAI), to correct an unsafe condition
for certain MHI RJ Aviation ULC Model CL-600-2C10 (Regional Jet Series
700, 701 & 702), CL-600-2C11 (Regional Jet Series 550), CL-600-2D15
(Regional Jet Series 705), CL-600-2D24 (Regional Jet Series 900), and
CL-600-2E25 (Regional Jet Series 1000) airplanes. You may examine the
MCAI in the AD docket at https://www.regulations.gov by searching for
and locating Docket No. FAA-2021-0382.

This proposed AD was prompted by a determination that new
airworthiness limitations for structural inspections and safe life
components are necessary. The FAA is proposing this AD to address reduced
structural integrity and reduced controllability of the airplane. See the
MCAI for additional background information.

Related Service Information Under 1 CFR Part 51

MHI RJ Aviation ULC has issued MHI RJ Service Bulletin 670BA-05-
001, dated August 27, 2020. This service information describes new
airworthiness limitations for structural inspections and safe life
components.

This service information is reasonably available because the
interested parties have access to it through their normal course of
business or by the means identified in the ADDRESSES section.

FAA's Determination

This product has been approved by the aviation authority of another
country, and is approved for operation in the United States. Pursuant
to the FAA's bilateral agreement with the State of Design Authority,
the FAA has been notified of the unsafe condition described in the MCAI
and service information referenced above. The FAA is proposing this AD
because the FAA evaluated all the relevant information and determined
the unsafe condition described previously is likely to exist or develop
on other products of the same type design.

Proposed AD Requirements in This NPRM

This proposed AD would require revising the existing maintenance or
inspection program, as applicable, to incorporate new airworthiness
limitations.

This proposed AD would require revisions to certain operator
maintenance documents to include new actions (e.g., inspections).
Compliance with these actions is required by 14 CFR 91.403(c). For
airplanes that have been previously modified, altered, or repaired in
the areas addressed by this proposed AD, the operator may not be able
to accomplish the actions described in the revisions. In this
situation, to comply with 14 CFR 91.403(c), the operator must request
approval for an alternative method of compliance according to paragraph
(i)(1) of this proposed AD.

Costs of Compliance

The FAA estimates that this AD, if adopted as proposed, would
affect 554 airplanes of U.S. registry. The FAA estimates the following
costs to comply with this proposed AD:

The FAA has determined that revising the maintenance or inspection
program takes an average of 90 work-hours per operator, although the
FAA recognizes that this number may vary from operator to operator. In
the past, the FAA has estimated that this action takes 1 work-hour per
airplane. Since operators incorporate maintenance or inspection program
changes for their affected fleet(s), the FAA has determined that a per-
operator estimate is more accurate than a per-airplane estimate.
Therefore, the FAA estimates the total cost per operator to be $7,650
(90 work-hours x $85 per work-hour).

Authority for This Rulemaking


Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.

The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.

Regulatory Findings

The FAA determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed
regulation:

(1) Is not a "significant regulatory action" under Executive
Order 12866,

(2) Will not affect intrastate aviation in Alaska, and

(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended]

2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive: