preamble attached >>>
ADs updated daily at www.Tdata.com
PROPOSED AD AIRBUS HELICOPTERS: Docket No. FAA-2021-0314; Project Identifier MCAI-2020-00599-R.
(a) COMMENTS DUE DATE

    The FAA must receive comments by May 24, 2021.

(b) AFFECTED AIRWORTHINESS DIRECTIVES (ADS)

    None.

(c) APPLICABILITY

    This  AD  applies  to Airbus  Helicopters  Model  EC155B1 helicopters,
    certificated in any category,  all serial numbers manufactured  before
    June 30, 2015, and equipped with a pilot or co-pilot door  jettisoning
    system in  accordance with  Airbus Helicopters  modification POST  MOD
    0752C05, except helicopters on which Aircraft Maintenance Manual (AMM)
    task 52-11-00-712 was  accomplished on both  pilot and co-pilot  doors
    since the last crew door installation.

(d) SUBJECT

    Joint  Aircraft  System  Component  (JASC)  Code  5210, Passenger/Crew
    Doors.

(e) REASON

    This AD was prompted by a report of difficulties when jettisoning  the
    co-pilot door  during non-scheduled  maintenance. The  FAA is  issuing
    this AD to address jamming of the affected door jettisoning mechanism,
    which could reduce  the ability of  the flightcrew to  evacuate in the
    event of an emergency situation.

(f) COMPLIANCE

    Comply  with this  AD within  the compliance  times specified,  unless
    already done.

(g) REQUIREMENTS

    Except  as specified  in paragraph  (h) of  this AD:  Comply with  all
    required actions and compliance times specified in, and in  accordance
    with  European Aviation  Safety Agency  (now European  Union  Aviation
    Safety Agency) (EASA) AD 2015-0157, dated July 30, 2015 (EASA AD  2015
    -0157).

(h) EXCEPTIONS TO EASA AD 2015-0157

(1) Where EASA AD 2015-0157 refers to its effective date, this AD requires
    using the effective date of this AD.

(2) The "Remarks" section of EASA AD 2015-0157 does not apply to this AD.

(3) Where EASA AD 2015-0157 refers to flight hours (FH), this AD  requires
    using hours time-in-service.

(4) Where paragraph (2) of EASA AD 2015-0157 provides an option to contact
    Airbus  Helicopters  for approved  instructions  and accomplish  those
    instructions, for this AD, the option is to repair the jettison system
    in accordance with FAA-approved procedures.

(5) Where the  service  information referenced in  EASA AD 2015-0157 spec-
    ifies to "speak to Airbus Helicopters," this AD requires repairing the
    jettison system in accordance with FAA-approved procedures.

(6) Where  the  service  information  referenced  in  EASA   AD  2015-0157
    specifies  to discard  certain parts,  this AD  requires removing  the
    parts from service instead.

(i) ALTERNATIVE METHODS OF COMPLIANCE (AMOCS)

(1) The Manager, International  Validation Branch, FAA, has  the authority
    to approve AMOCs for this AD, if requested using the procedures  found
    in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to
    your principal inspector or local Flight Standards District Office, as
    appropriate. If  sending information  directly to  the Manager  of the
    International Validation  Branch, send  it to:  Manager, International
    Validation Branch, FAA,  10101 Hillwood Pkwy.,  Fort Worth, TX  76177;
    telephone (817) 222-5110; email 9-AVS-AIR-730-AMOC@faa.gov.

(2) Before  using  any approved  AMOC, notify  your appropriate  principal
    inspector, or lacking a principal inspector, the manager of the  local
    flight standards district office/certificate holding  district office.

(j) RELATED INFORMATION

(1) For EASA AD 2015-0157, contact the EASA, Konrad-Adenauer-Ufer 3, 50668
    Cologne,    Germany;    telephone   +49    221    8999   000;    email
    ADs@easa.europa.eu;  internet  www.easa.europa.eu. You  may  find this
    EASA AD on the EASA website at https://ad.easa.europa.eu. You may view
    this material at  the FAA, Office  of the Regional  Counsel, Southwest
    Region, 10101 Hillwood Pkwy., Room  6N-321, Fort Worth, TX 76177.  For
    information on the availability of this material at the FAA, call  817
    -222-5110. This material may be found in the AD docket on the internet
    at https://www.regulations.gov  by searching  for and  locating Docket
    No. FAA-2021-0314.

(2) For  more  information about  this  AD,  contact  Kathleen  Arrigotti,
    Program  Manager,  Large  Aircraft  Section,  International Validation
    Branch, Compliance  & Airworthiness  Division, FAA,  2200 South  216th
    St.,  Des  Moines, WA  98198;  telephone and  fax  206-231-3218; email
    kathleen.arrigotti@faa.gov.

Issued  on  April 14,  2021.  Gaetano A.  Sciortino,  Deputy Director  for
Strategic  Initiatives,  Compliance  &  Airworthiness  Division,  Aircraft
Certification Service.

DATES: The FAA must receive comments on this  proposed AD by May 24, 2021.
PREAMBLE 

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration


14 CFR Part 39

[Docket No. FAA-2021-0314; Project Identifier MCAI-2020-00599-R]
RIN 2120-AA64

Airworthiness Directives; Airbus Helicopters

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD)
for certain Airbus Helicopters Model EC155B1 helicopters. This proposed
AD was prompted by a report of difficulties when jettisoning the co-
pilot door during non-scheduled maintenance. This proposed AD would
require a functional check of the pilot and co-pilot door jettisoning
system and corrective actions if necessary, as specified in a European
Aviation Safety Agency (EASA) AD, which is proposed for incorporation
by reference (IBR). The FAA is proposing this AD to address the unsafe
condition on these products.

DATES: The FAA must receive comments on this proposed AD by May 24, 2021.

ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:

Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow
the instructions for submitting comments.

Fax: 202-493-2251.

Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.

Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For material that is proposed for IBR in this AD, contact the EASA,
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999
000; email ADs@easa.europa.eu; internet www.easa.europa.eu. You may
find this material on the EASA website at https://ad.easa.europa.eu.
You may view this material at the FAA, Office of the Regional Counsel,
Southwest Region, 10101 Hillwood Pkwy., Room 6N-321, Fort Worth, TX
76177. For information on the availability of this material at the FAA,
call 817-222-5110. It is also available in the AD docket on the
internet at https://www.regulations.gov
by searching for and locating Docket No. FAA-2021-0314.

Examining the AD Docket


You may examine the AD docket on the internet at https://www.regulations.gov
by searching for and locating Docket No. FAA-2021-
0314; or in person at Docket Operations between 9 a.m. and 5 p.m.,
Monday through Friday, except Federal holidays. The AD docket contains
this NPRM, any comments received, and other information. The street
address for Docket Operations is listed above. Comments will be
available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Kathleen Arrigotti, Program Manager,
Large Aircraft Section, International Validation Branch, Compliance &
Airworthiness Division, FAA, 2200 South 216th St., Des Moines, WA
98198; telephone and fax 206-231-3218; email
kathleen.arrigotti@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited


The FAA invites you to send any written relevant data, views, or
arguments about this proposal. Send your comments to an address listed
under ADDRESSES. Include "Docket No. FAA-2021-0314; Project Identifier
MCAI-2020-00599-R" at the beginning of your comments. The most helpful
comments reference a specific portion of the proposal, explain the
reason for any recommended change, and include supporting data. The FAA
will consider all comments received by the closing date and may amend
this proposal because of those comments.
Except for Confidential Business Information (CBI) as described in
the following paragraph, and other information as described in 14 CFR
11.35, the FAA will post all comments received, without change, to
https://www.regulations.gov, including any personal information you
provide. The agency will also post a report summarizing each
substantive verbal contact received about this proposal.

Confidential Business Information


CBI is commercial or financial information that is both customarily
and actually treated as private by its owner. Under the Freedom of
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public
disclosure. If your comments responsive to this NPRM contain commercial
or financial information that is customarily treated as private, that
you actually treat as private, and that is relevant or responsive to
this NPRM, it is important that you clearly designate the submitted
comments as CBI. Please mark each page of your submission containing
CBI as "PROPIN." The FAA will treat such marked submissions as
confidential under the FOIA, and they will not be placed in the public
docket of this NPRM. Submissions containing CBI should be sent to
Kathleen Arrigotti, Program Manager, Large Aircraft Section,
International Validation Branch, Compliance & Airworthiness Division,
FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206-
231-3218; email kathleen.arrigotti@faa.gov. Any commentary that the FAA
receives that is not specifically designated as CBI will be placed in
the public docket for this rulemaking.

Discussion


The EASA (now European Union Aviation Safety Agency), which is the
Technical Agent for the Member States of the European Union, has issued
EASA AD 2015-0157, dated July 30, 2015 (EASA AD 2015-0157) (also
referred to as the Mandatory Continuing Airworthiness Information, or
the MCAI), to correct an unsafe condition for Airbus Helicopters Model
EC 155 B1 helicopters, all serial numbers delivered after manufacturing
before June 30, 2015, and equipped with a pilot or co-pilot door
jettisoning system in accordance with Airbus Helicopters Modification
POST MOD 0752C05, except helicopters on which Aircraft Maintenance
Manual (AMM) Task 52-11-00-712 was accomplished on both pilot and co-
pilot doors since the last crew door installation.

This proposed AD was prompted by a report of difficulties when
jettisoning the co-pilot door during non-scheduled maintenance. The FAA
is proposing this AD to address jamming of the affected door
jettisoning mechanism, which could reduce the ability of the flightcrew
to evacuate in the event of an emergency situation. See the MCAI for
additional background information.

Related IBR Material Under 1 CFR Part 51


EASA AD 2015-0157 describes procedures for doing a functional check
of the pilot and co-pilot door jettisoning system and corrective
actions. The corrective actions include greasing the tenons and
restoring the jettison system. This material is reasonably available
because the interested parties have access to it through their normal
course of business or by the means identified in the ADDRESSES section.

FAA's Determination and Requirements of This Proposed AD


This product has been approved by the aviation authority of another
country, and is approved for operation in the United States. Pursuant
to the bilateral agreement with the State of Design Authority, the FAA
has been notified of the unsafe condition described in the MCAI
referenced above. The FAA is proposing this AD after evaluating all the
relevant information and determining the unsafe condition described
previously is likely to exist or develop in other products of the same
type design.

Proposed AD Requirements


This proposed AD would require accomplishing the actions specified
in EASA AD 2015-0157, described previously, as incorporated by
reference, except for any differences identified as exceptions in the
regulatory text of this proposed AD.

Explanation of Required Compliance Information


In the FAA's ongoing efforts to improve the efficiency of the AD
process, the FAA initially worked with Airbus and EASA to develop a
process to use certain EASA ADs as the primary source of information
for compliance with requirements for corresponding FAA ADs. The FAA has
since coordinated with other manufacturers and civil aviation
authorities (CAAs) to use this process. As a result, EASA AD 2015-0157
will be incorporated by reference in the FAA final rule. This proposed
AD would, therefore, require compliance with EASA AD 2015-0157 in its
entirety, through that incorporation, except for any differences
identified as exceptions in the regulatory text of this proposed AD.
Using common terms that are the same as the heading of a particular
section in the EASA AD does not mean that operators need comply only
with that section. For example, where the AD requirement refers to
"all required actions and compliance times," compliance with this AD
requirement is not limited to the section titled "Required Action(s)
and Compliance Time(s)" in the EASA AD. Service information specified
in EASA AD 2015-0157 that is required for compliance with EASA AD 2015-
0157 will be available on the internet at https://www.regulations.gov
by searching for and locating Docket No. FAA-2021-0314 after the FAA
final rule is published.

Costs of Compliance


The FAA estimates that this proposed AD affects 14 helicopters of
U.S. registry. The FAA estimates the following costs to comply with
this proposed AD:

Estimated Costs for Required Actions

LABOR COST
PARTS COST
COST PER
PRODUCT
COST ON U.S. OPERATORS
8 work-hours x $85 per hour = $680
$0
$680
$9,520

The FAA estimates the following costs to do any necessary on-
condition action that would be required based on the results of any
required actions. The FAA has no way of determining the number of
helicopters that might need this on-condition action:

Estimated Costs of On-Condition Actions

LABOR COST PARTS COST COST PER
PRODUCT
1 work-hour x $85 per hour = $85 $0 $85

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.

The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.

Regulatory Findings


The FAA determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed regulation:

(1) Is not a "significant regulatory action" under Executive Order 12866,

(2) Would not affect intrastate aviation in Alaska, and

(3) Would not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39


Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.

The Proposed Amendment


Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES


1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended]


2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive: