preamble attached >>>
ADs updated daily at www.Tdata.com
PROPOSED AD DASSAULT AVIATION: Docket No. FAA-2019-0857; Product Identifier 2019-NM-124-AD.
(a) COMMENTS DUE DATE

    The FAA must receive comments by December 16, 2019.

(b) AFFECTED ADS

(1) This  AD  replaces  AD 2018-19-26,  Amendment  39-19427  (83 FR 49275,
    October 1, 2018) ("AD 2018-19-26").

(2) This AD affects 2010-26-05,  Amendment 39-16544 (75 FR 79952, December
    21, 2010) ("AD 2010-26-05").

(c) APPLICABILITY

    This AD applies to all Dassault Aviation Model MYSTERE-FALCON 200 air-
    planes, certificated in any category.

(d) SUBJECT

    Air  Transport  Association (ATA)  of  America Code  05,  Time Limits/
    Maintenance Checks.

(e) REASON

    This AD was prompted by  a determination that new or  more restrictive
    airworthiness limitations are necessary. The FAA is issuing this AD to
    address  fatigue   cracking,  damage,   and  corrosion   in  principal
    structural  elements;  such fatigue  cracking,  damage, and  corrosion
    could result in reduced structural integrity of the airplane.

(f) COMPLIANCE

    Comply  with this  AD within  the compliance  times specified,  unless
    already done.

(g) RETAINED REVISION OF MAINTENANCE OR INSPECTION PROGRAM WITH NO CHANGES

    This paragraph restates the requirements  of paragraph (g) of AD  2018
    -19-26, with no  changes. Within 90  days after November  5, 2018 (the
    effective date of AD 2018-19-26), revise the maintenance or inspection
    program, as applicable, to incorporate Chapter 5-40-00,  Airworthiness
    Limitations, Revision  17, dated  December 20,  2017, of  the Dassault
    Falcon  200  Maintenance  Manual.  The  initial  compliance  time  for
    accomplishing  the  actions is  at  the applicable  time  specified in
    Chapter  5-40-00,  Airworthiness   Limitations,  Revision  17,   dated
    December 20, 2017, of the  Dassault Falcon 200 Maintenance Manual;  or
    within 90 days after November 5,  2018 (the effective date of AD  2018
    -19-26); whichever occurs later.

(h) RETAINED NO ALTERNATIVE ACTIONS OR INTERVALS, WITH A NEW EXCEPTION

    This paragraph restates the requirements  of paragraph (h) of AD  2018
    -19-26, with a new exception.  Except as required by paragraph  (i) of
    this AD, after the maintenance or inspection program has been  revised
    as required by paragraph (g) of this AD, no alternative actions (e.g.,
    inspections) or intervals may be used unless the actions or  intervals
    are  approved  as  an  alternative  method  of  compliance  (AMOC)  in
    accordance with the procedures  specified in paragraph (l)(1)  of this
    AD.

(i) NEW MAINTENANCE OR INSPECTION PROGRAM REVISION

    Within  90  days after  the  effective date  of  this AD,  revise  the
    existing  maintenance  or   inspection  program,  as   applicable,  to
    incorporate   the   information   specified   in   Chapter    5-40-00,
    Airworthiness Limitations, Revision 18, dated January 15, 2019, of the
    Dassault Falcon  200 Maintenance  Manual. The  initial compliance time
    for  doing the  tasks is  at the  time specified  in Chapter  5-40-00,
    Airworthiness Limitations, Revision 18, dated January 15, 2019, of the
    Dassault Falcon 200  Maintenance Manual, or  within 90 days  after the
    effective date of this AD, whichever occurs later.

(j) NEW NO ALTERNATIVE ACTIONS OR INTERVALS

    After the existing maintenance or inspection program has been  revised
    as required by paragraph (i) of this AD, no alternative actions (e.g.,
    inspections) or intervals may be used unless the actions or  intervals
    are approved as an AMOC in accordance with the procedures specified in
    paragraph (l)(1) of this AD.

(k) TERMINATING ACTION FOR CERTAIN ACTIONS IN AD 2010-26-05

    Accomplishing the actions required by paragraph (g) or (i) of this  AD
    terminates the requirements of paragraph (g)(1) of AD 2010-26-05,  for
    Dassault Aviation Model MYSTERE-FALCON 200 airplanes.

(l) OTHER FAA AD PROVISIONS

    The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs):  The Manager, International
    Section, Transport Standards Branch, FAA, has the authority to approve
    AMOCs for this AD, if requested  using the procedures found in 14  CFR
    39.19. In  accordance with  14 CFR  39.19, send  your request  to your
    principal  inspector  or  local Flight  Standards District  Office, as
    appropriate.  If  sending information  directly  to the  International
    Section,  send  it  to  the  attention  of  the  person  identified in
    paragraph (m)(2) of this AD.  Information may be emailed to:  9-NM-116
    -AMOC-REQUESTS@faa.gov.

(i) Before using any approved AMOC,  notify your appropriate principal in-
    spector, or lacking  a principal inspector,  the manager of  the local
    flight standards district office/certificate holding district office.

(ii) AMOCs approved previously for AD 2018-19-26,  are  approved  as AMOCs
     for the corresponding provisions of this AD.

(2) Contacting the Manufacturer:  For any requirement in this AD to obtain
    corrective  actions   from  a   manufacturer,  the   action  must   be
    accomplished using  a method  approved by  the Manager,  International
    Section,  Transport  Standards  Branch,  FAA;  or  the  European Union
    Aviation  Safety Agency  (EASA);  or  Dassault Aviation's  EASA Design
    Organization Approval (DOA). If approved by the DOA, the approval must
    include the DOA-authorized signature.

(m) RELATED INFORMATION

(1) Refer to Mandatory Continuing Airworthiness Information (MCAI) EASA AD
    2019-0153, dated July 3, 2019, for related information.  This MCAI may
    be found in the AD docket on the internet  at  http://www.regulations.
    gov by searching for and locating Docket No. FAA-2019-0857.

(2) For more information about this AD,  contact Tom Rodriguez,  Aerospace
    Engineer, International Section, Transport Standards Branch, FAA, 2200
    South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3226.

(3) For service information identified in this AD, contact Dassault Falcon
    Jet Corporation, Teterboro Airport,  PO Box 2000, South Hackensack, NJ
    07606; telephone 201-440-6700; internet http://www.dassaultfalcon.com.
    You may view this service information at the FAA,  Transport Standards
    Branch,  2200 South 216th St., Des Moines, WA.  For information on the
    availability of this material at the FAA, call 206-231-3195.

Issued in Des Moines, Washington on October 22, 2019. Dionne Palermo, Act-
ing Director, System Oversight Division, Aircraft Certification Service.

DATES: The FAA must receive comments  on this proposed AD  by December 16,
2019.
PREAMBLE 

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0857; Product Identifier 2019-NM-124-AD]
RIN 2120-AA64

Airworthiness Directives; Dassault Aviation Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to supersede Airworthiness Directive (AD)
2018-19-26, which applies to all Dassault Aviation Model MYSTERE-
FALCON 200 airplanes. AD 2018-19-26 requires revising the maintenance
or inspection program, as applicable, to incorporate new or more
restrictive maintenance requirements and airworthiness limitations.
Since the FAA issued AD 2018-19-26, the FAA determined that new or more
restrictive airworthiness limitations are necessary. This proposed AD
would require revising the existing maintenance or inspection program,
as applicable, to incorporate new or more restrictive airworthiness
limitations. The FAA is proposing this AD to address the unsafe
condition on these products.

DATES: The FAA must receive comments on this proposed AD by December
16, 2019.

ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:

Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the
instructions for submitting comments.

Fax: 202-493-2251.

Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.

Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this NPRM, contact Dassault
Falcon Jet Corporation, Teterboro Airport, P.O. Box 2000, South
Hackensack, NJ 07606; telephone 201-440-6700; internet http://www.
dassaultfalcon.com. You may view this service information at the
FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA.
For information on the availability of this material at the FAA, call
206-231-3195.

Examining the AD Docket

You may examine the AD docket on the internet at http://www.regulations.
gov by searching for and locating Docket No. FAA-2019-0857;
or in person at Docket Operations between 9 a.m. and 5 p.m.,
Monday through Friday, except Federal holidays. The AD docket contains
this NPRM, the regulatory evaluation, any comments received, and other
information. The street address for Docket Operations is listed above.
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer,
International Section, Transport Standards Branch, FAA, 2200 South
216th St., Des Moines, WA 98198; telephone and fax 206-231-3226.

SUPPLEMENTARY INFORMATION:

Comments Invited

The FAA invites you to send any written relevant data, views, or
arguments about this proposal. Send your comments to an address listed
under the ADDRESSES section. Include "Docket No. FAA-2019-0857;
Product Identifier 2019-NM-124-AD" at the beginning of your comments.
The FAA specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of this NPRM. The FAA will
consider all comments received by the closing date and may amend this
NPRM because of those comments.

The FAA will post all comments, without change, to http://www.regulations.
gov, including any personal information you provide.
The FAA will also post a report summarizing each substantive verbal
contact the agency receives about this NPRM.

Discussion

The FAA issued AD 2018-19-26, Amendment 39-19427 (83 FR 49275,
October 1, 2018) ("AD 2018-19-26"), for all Dassault Aviation Model
MYSTERE-FALCON 200 airplanes. AD 2018-19-26 requires revising the
maintenance or inspection program, as applicable, to incorporate new or
more restrictive maintenance requirements and airworthiness
limitations. AD 2018-19-26 resulted from a determination that new or
more restrictive maintenance requirements and airworthiness limitations
are necessary. The FAA issued AD 2018-19-26 to address fatigue
cracking, damage, and corrosion in principal structural elements; such
fatigue cracking, damage, and corrosion could result in reduced
structural integrity of the airplane.

AD 2010-26-05, Amendment 39-16544 (75 FR 79952, December 21, 2010)
requires repetitive inspections for overpressure tightness on both
regulating valves; these inspections have since been incorporated into
the airworthiness limitations document for the affected airplanes.
Therefore, accomplishing the actions in this proposed AD would
terminate the requirements of paragraph (g)(1) of AD 2010-26-05 for
Dassault Aviation Model MYSTERE-FALCON 200 airplanes.

Actions Since AD 2018-19-26 Was Issued

Since the FAA issued AD 2018-19-26, the agency has determined that
new or more restrictive airworthiness limitations are necessary.

The European Union Aviation Safety Agency (EASA), which is the
Technical Agent for the Member States of the European Union, has issued
EASA AD 2019-0153, dated July 3, 2019 (referred to after this as the
Mandatory Continuing Airworthiness Information, or "the MCAI"), to
correct an unsafe condition for all Dassault Aviation Model MYSTERE-
FALCON 200 airplanes.

This proposed AD was prompted by a determination that new or more
restrictive airworthiness limitations are necessary. The FAA is
proposing this AD to address fatigue cracking, damage, and corrosion in
principal structural elements; such fatigue cracking, damage, and
corrosion could result in reduced structural integrity of the airplane.
See the MCAI for additional background information.

You may examine the MCAI in the AD docket on the internet at http://www.
regulations.gov by searching for and locating Docket No. FAA-2019-0857.

Related Service Information Under 1 CFR Part 51

Dassault Aviation has issued Chapter 5-40-00, Airworthiness
Limitations, Revision 18, dated January 15, 2019, of the Dassault
Falcon 200 Maintenance Manual. This service information describes
mandatory maintenance tasks that operators must perform at specified
intervals. This service information is reasonably available because the
interested parties have access to it through their normal course of
business or by the means identified in the ADDRESSES section.

FAA's Determination

This product has been approved by the aviation authority of another
country, and is approved for operation in the United States. Pursuant
to the FAA's bilateral agreement with the State of Design Authority,
the FAA has been notified of the unsafe condition described in the MCAI
and service information referenced above. The FAA is proposing this AD
because the FAA evaluated all the relevant information and determined
the unsafe condition described previously is likely to exist or develop
on other products of the same type design.

Proposed Requirements of This NPRM

This proposed AD would require revising the existing maintenance or
inspection program, as applicable, to incorporate new or more
restrictive airworthiness limitations.

This proposed AD would require revisions to certain operator
maintenance documents to include new actions (e.g., inspections).
Compliance with these actions is required by 14 CFR 91.403(c). For
airplanes that have been previously modified, altered, or repaired in
the areas addressed by this proposed AD, the operator may not be able
to accomplish the actions described in the revisions. In this
situation, to comply with 14 CFR 91.403(c), the operator must request
approval for an alternative method of compliance according to paragraph
(l)(1) of this proposed AD.

Costs of Compliance

The FAA estimates that this proposed AD affects 9 airplanes of U.S.
registry. The FAA estimates the following costs to comply with this
proposed AD:

The FAA estimates the total cost per operator for the retained
actions from AD 2018-19-26 to be $7,650 (90 work-hours x $85 per work-
hour).

The FAA has determined that revising the existing maintenance or
inspection program takes an average of 90 work-hours per operator,
although the FAA recognizes that this number may vary from operator to
operator. In the past, the FAA has estimated that this action takes 1
work-hour per airplane. Since operators incorporate maintenance or
inspection program changes for their affected fleet(s), the FAA has
determined that a per-operator estimate is more accurate than a per-
airplane estimate. Therefore, the FAA estimates the total cost per
operator to be $7,650 (90 work-hours x $85 per work-hour).

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.

The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: "General
requirements." Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.

This proposed AD is issued in accordance with authority delegated
by the Executive Director, Aircraft Certification Service, as
authorized by FAA Order 8000.51C. In accordance with that order,
issuance of ADs is normally a function of the Compliance and
Airworthiness Division, but during this transition period, the
Executive Director has delegated the authority to issue ADs applicable
to transport category airplanes and associated appliances to the
Director of the System Oversight Division.

Regulatory Findings

The FAA determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed
regulation:

(1) Is not a "significant regulatory action" under Executive
Order 12866,

(2) Will not affect intrastate aviation in Alaska, and

(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended]

2. The FAA amends Sec. 39.13 by removing Airworthiness Directive (AD)
2018-19-26, Amendment 39-19427 (83 FR 49275, October 1, 2018), and
adding the following new AD: