preamble attached >>>
ADs updated daily at www.Tdata.com
PROPOSED AD DASSAULT AVIATION: Docket No. FAA-2019-0697; Product Identifier 2019-NM-110-AD.
(a) COMMENTS DUE DATE

    The FAA must receive comments by October 28, 2019.

(b) AFFECTED ADS

(1) This  AD  replaces  AD 2014-16-27,  Amendment  39-17951  (79 FR 51071,
    August 27, 2014) ("AD 2014-16-27");  and AD 2017-19-14,  Amendment 39-
    19044 (82 FR 43674, September 19, 2017) ("AD 2017-19-14").

(2) This  AD  affects  AD 2010-26-05,  Amendment  39-16544  (75 FR 79952,
    December 21, 2010) ("AD 2010-26-05").

(c) APPLICABILITY

    This  AD  applies  to  Dassault Aviation Model FALCON 900EX airplanes,
    serial number  (S/N) 97  and S/N  120 and  higher, certificated in any
    category,  with  an  original  airworthiness  certificate  or original
    export certificate of airworthiness  issued on or before  September 1,
    2018.

(d) SUBJECT

    Air  Transport  Association  (ATA)  of  America Code 05,  Time Limits/
    Maintenance Checks.

(e) REASON

    This AD was prompted by  a determination that new or  more restrictive
    airworthiness limitations are necessary. The FAA is issuing this AD to
    address reduced structural integrity of the airplane.

(f) COMPLIANCE

    Comply with this AD within the compliance times specified,  unless al-
    ready done.

(g) RETAINED REVISION OF MAINTENANCE OR INSPECTION PROGRAM WITH NO CHANGES

    This paragraph restates  the requirements of paragraph (g) of AD 2017-
    19-14, with  no changes.  Within 90  days after  October 24, 2017 (the
    effective date of AD 2017-19-14), revise the maintenance or inspection
    program, as  applicable, to  incorporate the  information specified in
    Chapter 5-40,  Airworthiness Limitations,  Revision 9,  dated November
    2015, of  the Dassault  Falcon 900EX  EASy, Falcon  900LX, and  Falcon
    900DX   Maintenance   Manual.   The   initial   compliance   time  for
    accomplishing  the actions  specified in  Chapter 5-40,  Airworthiness
    Limitations, Revision 9, dated  November 2015, of the  Dassault Falcon
    900EX  EASy, Falcon  900LX, and  Falcon 900DX  Maintenance Manual,  is
    within the applicable times specified in the maintenance manual or  90
    days  after  October  24,  2017,  whichever  occurs  later,  except as
    provided by paragraphs (g)(1) through (g)(4) of this AD.

(1) The term "LDG"  in the "First Inspection" column of any table  in  the
    service information means total airplane landings.

(2) The term "FH"  in the "First Inspection" column  of any table  in  the
    service information means total flight hours.

(3) The term "FC"  in the "First Inspection" column  of any table  in  the
    service information means total flight cycles.

(4) The term "M" in the "First Inspection" column of any table in the ser-
    vice information means months.

(h) RETAINED NO ALTERNATIVE ACTIONS AND INTERVALS, WITH NEW EXCEPTION

    This paragraph restates the requirements specified in paragraph (h) of
    AD 2017-19-14, with a new  exception. Except as required by  paragraph
    (i) of this AD, after accomplishing the revision required by paragraph
    (g) of this AD, no alternative actions (inspections) or intervals  may
    be used unless the actions or intervals are approved as an alternative
    method  of  compliance  (AMOC)  in  accordance  with  the   procedures
    specified in paragraph (l)(1) of this AD.

(i) NEW REQUIREMENT OF THIS AD: MAINTENANCE OR INSPECTION PROGRAM REVISION

    Within 90 days after the effective date of this AD,  revise the exist-
    ing maintenance or inspection  program, as applicable, to  incorporate
    the information specified in Chapter 5-40, Airworthiness  Limitations,
    Revision 11, dated September 2018, of the Dassault Falcon 900EX  EASy,
    Falcon  900LX,  and  Falcon  900DX  Maintenance  Manual.  The  initial
    compliance time for accomplishing  the actions specified in  Chapter 5
    -40, Airworthiness Limitations, Revision 11, dated September 2018,  of
    the  Dassault  Falcon  900EX  EASy,  Falcon  900LX,  and  Falcon 900DX
    Maintenance Manual, is  within the applicable  times specified in  the
    maintenance manual, or  90 days after  the effective date  of this AD,
    whichever  occurs  later,  except  as  provided  by  paragraphs (i)(1)
    through (i)(4) of this AD.

(1) The term "LDG"  in the "First Inspection" column  of any table  in the
    service information means total airplane landings.

(2) The term "FH"  in the "First Inspection" column  of any table  in  the
    service information means total flight hours.

(3) The term "FC"  in the "First Inspection" column  of any table  in  the
    service information means total flight cycles.

(4) The term "M" in the "First Inspection" column of any table in the ser-
    vice  information  means months  since  the date  of  issuance of  the
    original  airworthiness certificate  or the  date of  issuance of  the
    original export certificate of airworthiness.

(j) NO ALTERNATIVE ACTIONS OR INTERVALS

    After the existing maintenance or inspection program has been  revised
    as required by paragraph (i) of this AD, no alternative actions (e.g.,
    inspections) or intervals may be used unless the actions and intervals
    are approved as an AMOC in accordance with the procedures specified in
    paragraph (l)(1) of this AD.

(k) TERMINATING ACTIONS FOR CERTAIN ACTIONS IN AD 2010-26-05

    Accomplishing the actions required  by paragraph (g) or (i) of this AD
    terminates the requirements of paragraph (g)(1) of AD 2010-26-05,  for
    Dassault Aviation Model 900EX airplanes S/N 97 and S/N 120 and higher.

(l) OTHER FAA AD PROVISIONS

(1) Alternative Methods of Compliance (AMOCs):  The Manager, International
    Section, Transport Standards Branch, FAA, has the authority to approve
    AMOCs for this AD, if requested  using the procedures found in 14  CFR
    39.19. In  accordance with  14 CFR  39.19, send  your request  to your
    principal  inspector  or  local Flight  Standards District  Office, as
    appropriate.  If  sending information  directly  to the  International
    Section,  send  it  to  the  attention  of  the  person  identified in
    paragraph (m)(2) of this AD.  Information may be emailed to  9-ANM-116
    -AMOC-REQUESTS@faa.gov. Before  using any  approved AMOC,  notify your
    appropriate principal inspector, or lacking a principal inspector, the
    manager  of  the local  flight  standards district  office/certificate
    holding district office.

(2) Contacting the Manufacturer:  As of the effective date of this AD, for
    any  requirement  in  this  AD to  obtain  corrective  actions  from a
    manufacturer, the action must be accomplished using a method  approved
    by  the Manager,  International Section,  Transport Standards  Branch,
    FAA; or the European Union Aviation Safety Agency (EASA); or  Dassault
    Aviation's EASA Design Organization Approval (DOA). If approved by the
    DOA, the approval must include the DOA-authorized signature.

(m) RELATED INFORMATION

(1) Refer to Mandatory Continuing Airworthiness Information (MCAI) EASA AD
    2019-0134, dated June 11, 2019, for related information. This MCAI may
    be found in the AD docket  on the internet  at http://www.regulations.
    gov by searching for and locating Docket No. FAA-2019-0697.

(2) For more information about this AD,  contact Tom Rodriguez,  Aerospace
    Engineer, International Section, Transport Standards Branch, FAA, 2200
    South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3226.

(3) For service information identified in this AD, contact Dassault Falcon
    Jet Corporation, Teterboro Airport,  PO Box 2000, South Hackensack, NJ
    07606; telephone 201-440-6700; internet http://www.dassaultfalcon.com.
    You may view this service information at the FAA,  Transport Standards
    Branch,  2200 South 216th St., Des Moines, WA.  For information on the
    availability of this material at the FAA, call 206-231-3195.

Issued in Des Moines, Washington, on September 6, 2019.  Michael Kaszycki,
Acting Director, System Oversight Division, Aircraft Certification Service

DATES: The FAA must receive comments  on this proposed AD  by  October 28,
2019.
PREAMBLE 

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0697; Product Identifier 2019-NM-110-AD]
RIN 2120-AA64

Airworthiness Directives; Dassault Aviation Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to supersede Airworthiness Directive (AD)
2017-19-14 and AD 2014-16-27, which apply to certain Dassault Aviation
Model FALCON 900EX airplanes. Those ADs require revising the existing
maintenance or inspection program, as applicable, to incorporate new or
more restrictive maintenance requirements and/or airworthiness
limitations. Since the FAA issued AD 2017-19-14 and AD 2014-16-27, the
FAA determined that new or more restrictive airworthiness limitations
are necessary. This proposed AD would require revising the existing
maintenance or inspection program, as applicable, to incorporate new or
more restrictive airworthiness limitations. The FAA is proposing this
AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by October 28,
2019.

ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:

Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the
instructions for submitting comments.

Fax: 202-493-2251.

Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.

Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this NPRM, contact Dassault
Falcon Jet Corporation, Teterboro Airport, P.O. Box 2000, South
Hackensack, NJ 07606; telephone 201-440-6700; internet http://www.
dassaultfalcon.com. You may view this referenced service information
at the FAA, Transport Standards Branch, 2200 South 216th St., Des
Moines, WA. For information on the availability of this material at
the FAA, call 206-231-3195.

Examining the AD Docket

You may examine the AD docket on the internet at http://www.regulations.
gov by searching for and locating Docket No. FAA-2019-0697;
or in person at Docket Operations between 9 a.m. and 5 p.m.,
Monday through Friday, except Federal holidays. The AD docket contains
this NPRM, the regulatory evaluation, any comments received, and other
information. The street address for Docket Operations is listed above.
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer,
International Section, Transport Standards Branch, FAA, 2200 South
216th St., Des Moines, WA 98198; telephone and fax 206-231-3226.

SUPPLEMENTARY INFORMATION:

Comments Invited

The FAA invites you to send any written relevant data, views, or
arguments about this proposal. Send your comments to an address listed
under the ADDRESSES section. Include "Docket No. FAA-2019-0697;
Product Identifier 2019-NM-110-AD" at the beginning of your comments.
The FAA specifically invites comments on the overall regulatory,
economic, environmental, and energy aspects of this proposed AD. The
FAA will consider all comments received by the closing date and may
amend this proposed AD based on those comments.

The FAA will post all comments received, without change, to http://www.
regulations.gov, including any personal information you provide.
The FAA will also post a report summarizing each substantive verbal
contact received about this proposed AD.

Discussion

The FAA issued AD 2017-19-14, Amendment 39-19044 (82 FR 43674,
September 19, 2017) ("AD 2017-19-14"), for certain Dassault Aviation
Model FALCON 900EX airplanes. AD 2017-19-14 requires revising the
existing maintenance or inspection program, as applicable, to
incorporate new or more restrictive maintenance requirements and/or
airworthiness limitations. AD 2017-19-14 resulted from a determination
that new or more restrictive maintenance requirements and/or
airworthiness limitations are necessary. AD 2017-19-14 specifies that
accomplishing the actions required by that AD would terminate the
requirements of AD 2014-16-27, Amendment 39-17951 (79 FR 51071, August
27, 2014) ("AD 2014-16-27") but it did not supersede AD 2014-16-27.
In addition, AD 2014-16-27 specifies that accomplishing paragraph (g)
of that AD would terminate the requirements of paragraph (g)(1) of AD
2010-26-05, Amendment 39-16544 (75 FR 79952, December 21, 2010), for
Dassault Aviation Model 900EX airplanes, serial number (S/N) 97 and S/N
120 and higher. This terminating provision of certain requirements of
AD 2010-26-05 is part of this proposed AD.

This AD proposes to supersede AD 2017-19-14 and AD 2014-16-27 but
does not propose to supersede AD 2010-26-05.

Actions Since AD 2017-19-14 and AD 2014-16-27 Were Issued

Since the FAA issued AD 2017-19-14 and AD 2014-16-27, the FAA has
determined that new or more restrictive airworthiness limitations are
necessary.

The European Union Aviation Safety Agency (EASA), which is the
Technical Agent for the Member States of the European Union, has issued
EASA AD 2019-0134, dated June 11, 2019 (referred to after this as the
Mandatory Continuing Airworthiness Information, or "the MCAI"), to
correct an unsafe condition for certain Dassault Aviation Model FALCON
900EX airplanes. The MCAI states:

The airworthiness limitations for certain Falcon 900EX
aeroplanes, which are approved by EASA, are currently defined and
published in Dassault Falcon 900EX Easy/900LX/900DX AMM [Airplane
Maintenance Manual], Chapter 5-40. These instructions have been
identified as mandatory for continued airworthiness.

Failure to accomplish these instructions could result in an
unsafe condition.

EASA previously issued AD 2016-0129 (which corresponds to FAA AD
2017-19-14), requiring the actions described in Dassault Falcon
900EX Easy/900LX/900DX AMM Chapter 5-40 (DGT113875) at Revision 9.

Since that [EASA] AD was issued, Dassault published Revisions 10
and 11 of Dassault Falcon 900EX Easy/900LX/900DX AMM Chapter 5-40
(DGT113875). Revision 11 contains new and/or more restrictive
maintenance tasks.

For the reason described above, this [EASA] AD retains the
requirements of EASA AD 2016-0129, which is superseded, and
requires accomplishment of the actions specified in the ALS
[airworthiness limitations section], as defined in this [EASA] AD.

You may examine the MCAI in the AD docket on the internet at http://www.
regulations.gov by searching for and locating Docket No. FAA-2019-0697.

Related Service Information Under 1 CFR Part 51

Dassault Aviation has issued Chapter 5-40, Airworthiness
Limitations, Revision 11, dated September 2018, of the Falcon 900EX
EASy, Falcon 900LX, and Falcon 900DX Maintenance Manual. This service
information describes procedures, maintenance tasks, and airworthiness
limitations specified in the Airworthiness Limitations section of the
AMM.

This proposed AD would also require Chapter 5-40, Airworthiness
Limitations, Revision 9, dated November 2015, of the Dassault Falcon
900EX EASy, Falcon 900LX, and Falcon 900DX Maintenance Manual, which
the Director of the Federal Register approved for incorporation by
reference as of October 24, 2017 (82 FR 43674, September 19, 2017).

This service information is reasonably available because the
interested parties have access to it through their normal course of
business or by the means identified in the ADDRESSES section.

FAA's Determination

This product has been approved by the aviation authority of another
country, and is approved for operation in the United States. Pursuant
to a bilateral agreement with the State of Design Authority, the FAA
has been notified of the unsafe condition described in the MCAI and
service information referenced above. The FAA is proposing this AD
because the agency evaluated all the relevant information and
determined the unsafe condition described previously is likely to exist
or develop on other products of the same type design.

Proposed Requirements of This NPRM

This proposed AD would retain all of the requirements of AD 2017-
19-14. This proposed AD would require revising the existing maintenance
or inspection program, as applicable, to incorporate new or more
restrictive airworthiness limitations. This proposed AD would also
retain the terminating provision of AD 2014-16-27, related to AD 2010-
26-05.

This proposed AD would require revisions to certain operator
maintenance documents to include new actions (e.g., inspections).
Compliance with these actions is required by 14 CFR 91.403(c). For
airplanes that have been previously modified, altered, or repaired in
the areas addressed by this proposed AD, the operator may not be able
to accomplish the actions described in the revisions. In this
situation, to comply with 14 CFR 91.403(c), the operator must request
approval for an alternative method of compliance according to paragraph
(l)(1) of this proposed AD.

Costs of Compliance

The FAA estimates that this proposed AD affects 79 airplanes of
U.S. registry.

The FAA estimates the following costs to comply with this proposed
AD:

The FAA estimates the total cost per operator for the retained
actions from AD 2017-19-14 to be $7,650 (90 work-hours x $85 per work-
hour).

The FAA has determined that revising the existing maintenance or
inspection program takes an average of 90 work-hours per operator,
although the agency recognizes that this number may vary from operator
to operator. In the past, the FAA has estimated that this action takes
1 work-hour per airplane. Since operators incorporate maintenance or
inspection program changes for their affected fleet(s), the FAA has
determined that a per-operator estimate is more accurate than a per-
airplane estimate.

The FAA estimates the total cost per operator for the new proposed
actions to be $7,650 (90 work-hours x $85 per work-hour).

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.

The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: "General
requirements." Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.

This proposed AD is issued in accordance with authority delegated
by the Executive Director, Aircraft Certification Service, as
authorized by FAA Order 8000.51C. In accordance with that order,
issuance of ADs is normally a function of the Compliance and
Airworthiness Division, but during this transition period, the
Executive Director has delegated the authority to issue ADs applicable
to transport category airplanes and associated appliances to the
Director of the System Oversight Division.

Regulatory Findings

The FAA determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed
regulation:

(1) Is not a "significant regulatory action" under Executive
Order 12866,

(2) Will not affect intrastate aviation in Alaska, and

(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended]

2. The FAA amends Sec. 39.13 by

a. Removing Airworthiness Directive (AD) 2014-16-27, Amendment 39-17951
(79 FR 51071, August 27, 2014); and AD 2017-19-14, Amendment 39-19044
(82 FR 43674, September 19, 2017); and

b. Adding the following new AD: